Osaka Stainless Co., Ltd.

News Products About us Facilities Contact Site map
 

Nickel Alloy/Titanium

Below you can find our current stock of Alloy 625 (Inconel 625). We Specialise in Round Bars, Hex Bars, Hex Bolts, Nuts, Washers, Wire Rods and Flanges.

Characteristics

ALLOY625 is a low-carbon Ni-Cr-Mo-Nb alloy which shows excellent resistance to a
variety of corrosive media.

  • outstanding resistance to pitting, crevice corrosion, erosion and intergranular attack
  • almost complete freedom from chloride-induced stress-corrosion cracking
  • good resistance to mineral acids, such as nitric, phosphoric, sulphuric and hydrochloric acids
  • good resistance to alkalis and organic acids
  • good mechanical properties
Density

8.44

Stock Form and Sizes

Round BarSpecification:ASTMB446/B564¦@ASME SB446/SB564¦@AMS5666@NACE MR0175(ISO 15156)
¦B564/SB564 Apply to Forged Bar Only
Stock Specification: Grade 1(Annealed)
Dia.1mm-10mm
1.2 1.6 2 2.6 3 3.5 4 4.4 5 5.3 6 7.1 8 8.95 10
             £   £   £
Dia.12mm-38mm
12 13 16 18 19 20 22 24 25 28 30 32 35 36 38
£ š š š   š š   š š š š š   š
Dia.40mm-105mm
40 42 45 50 55 60 65 70 75 80 85 90 95 100 105
š š š š š š š š š š š š š š  
Dia.110mm-200mm
110 115 120 125 130 135 140 145 150 160 165 170 180 190 200
š   š   š   š   š š     š   š
Dia.210mm-300mm
210 220 230 250 280 300                  
    š š
254
š                    

¦@Ÿ1000‡o@2000‡o@£3000‡o@¡3500‡o@œ4000‡o@š2500‡o`3990‡o
¦@Rolling Thread sizes available in C276(M4 to M10)

Hex BarSpecification: ASTM B446
A/F(mm) 10 13 14 17 19 21 22 24 26 27 30 32 36
/ š š   š š     š          

¦@š2500‡o`3990‡o

Nut & WasherSpecification: Nut JIS B1181 Class1    Washer, JIS B1256 Normal Series Grade.A
M4 M5 M6 M8 M10 M12 M16 M20 M24
  œ œ œ œ œ œ    

Sourcable Ex-Stock Material for Other Forms from Japanese Distributor

Plate Pipe Welding
Rod & Wire
Wire
Min Max
0.5`20mm ¢ ™ ™

¦@¢EEELimited Sizes Only@™EEEPlease enquire

Corrosion resistance

For optimal corrosion resistance the material must be in a clean condition and free from all kinds of contaminants before any fabricated component is placed into service. Under these conditions ALLOY625 exhibits excellent corrosion resistance in a wide variety of media:

  • excellent resistance to pitting and crevice corrosion in chloride-bearing media
  • essentially resistant to chloride-induced stress-corrosion cracking
  • high resistance against impingement and erosion corrosion
  • high resistance to corrosive attack by mineral acids, such as nitric, phosphoric, sulphuric and hydrochloric acids, as well as to alkalis and organic acids in both oxidizing and reducing conditions
  • practically no corrosive attack in marine and industrial atmosphrers. High resistance to seawater and brackish water, even at higher temperatures
  • high resistance against intergranular corrosion following thermal treatment and welding

The solution-annealed version (grade 2) shows good resistance to many corrosive gas atmospheres:

  • good resistance to carburization and to oxidation under
  • resistance to nitridation
  • good resistance to halogen containing gases and to hydrogen chloride

Applications

The soft-annealed version of Nicrofer 6020 hMo (grade 1) is preferred for applications in the chemical process industry, in marine engineering and in pollution control equipment for environmental protection.

Typical applications are:

  • superphosphoric acid production equipment
  • nuclear waste reprocessing equipment
  • sour gas production tubes
  • piping systems and sheathing of risers in oil exploration
  • offshore industry and marine equipment
  • flue gas scrubber and damper components
  • chimney linings

For high-temperature applications, up to approximately 1000 ‹C (1830 ‹F), the solution-annealed version of alloy 625 (grade 2) can be used in accordance to the ASME code for pressure vessels. For design calculations for equipment for use within the temperature range of approximately 500 ?1000 ‹C (930 ? 1830 ‹F) the loss in ductility resulting from prolonged exposure within that temperature range must be kept in mind

  • components in waste gas systems and waste gas cleaning plants exposed to higher temperatures
  • flare stacks in refineries and offshore platforms
  • recuperators and compensators
  • submarine diesel engine exhaust systems
  • superheater tubes in waste incineration plants
  • cladding of waterwall sections and superheater tubes in waste incineration plants by overlay welding

Chemical composition

  Ni Cr Fe C Mn Si Mo Co
min(%) 58.0 20.0         8.0  
max(%)   23.5 5.0 0.10 0.50 0.50 10.0 1.0
  Al Ti Nb+Ta P S
min(%)     3.15    
max(%) 0.40 0.40 4.15 0.015 0.015

Mechanical propertiesiRound Barj

  Condition Yield Strength(Mpa) Tensile Strength(Mpa) Elongation(%) Hardness(HB)
ASTM Min Value Soft Annealed 413 827 30  
Typical Values at RT Hot worked 588 980 45 210
Typical Values at RT Soft Annealed 539 931 45 180

Please contact us with any questions about reference or value of plate and pipe.

International Specification Comparison chart

  Material Round Bar Plate Pipe
Seamless Welded
ASTM UNS
N06625
B446 B443 B444 B704/705
ASME SB446 SB443 SB444  
JIS NCF625 H4553 G4901 H4552  
DIN 2.4856 17752 17750 17751  
Disclaimer:
All the information on this website is published in good faith and for general information purpose only and not for technical design purposes. We do not make any warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information on our website is strictly at your own risk. and we will not be liable for any losses and damages in connection with the use of our website.

     
To top of the page