SUS303
Characteristics
With sulphur added to SUS304, SUS303 has the best machinability in austenitic stainless steels.
Although sulphur improves machinability, it slightly reduces corrosion resistance. Therefore, its corrosion resistance is lower than SUS304.
Stock Form and Sizes
◆1000mm ◎2000mm ▲3000mm ■3500mm ●4000mm ★2500mm～3990mm
Cold finished round barsSpecification：JIS G4318、ASME A582、EN 1.4305*3mm-20mm are SUS303Cu
| Size 2〜8 | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 2 | 2.5 | 3 | 3.5 | 4 | 4.4 | 5 | 5.3 | 5.5 | 6 | 6.35 | 7 | 7.1 | 8 | 8.4 |
| ◎ | ◎ | ◎ | ◎ | ◎ | ▲ | |||||||||
| Size 8〜15 | ||||||||||||||
| 8.95 | 9 | 9.52 | 10 | 10.8 | 11 | 11.3 | 12 | 12.7 | 13 | 14 | 14.3 | 14.6 | 15 | 15.87 |
| ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ||||||||
| Size 16〜24 | ||||||||||||||
| 16 | 16.3 | 17 | 17.3 | 18 | 18.3 | 19 | 20 | 20.3 | 21 | 22 | 22.2 | 23 | 23.3 | 24 |
| ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ||||||
| Size 25〜42 | ||||||||||||||
| 25 | 26 | 27 | 27.62 | 28 | 30 | 30.6 | 32 | 33 | 33.3 | 34 | 35 | 36 | 38 | 40 |
| ▲ | ▲ | ▲ | ▲ | |||||||||||
| Size 45～50 | ||||||||||||||
| 42 | 45 | 48 | 50 | |||||||||||
Peeled round barsSpecification：JIS G4303、ASME A582、EN 1.4305
| Size 8〜26 | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 8 | 10 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 22 | 24 | 25 | 26 |
| ● | ● | ● | ● | |||||||||||
| Size 27〜48 | ||||||||||||||
| 27 | 28 | 30 | 32 | 33 | 34 | 35 | 36 | 38 | 40 | 42 | 44 | 45 | 46 | 48 |
| ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | |||||
| Size 50〜140 | ||||||||||||||
| 50 | 55 | 60 | 65 | 70 | 75 | 80 | 85 | 90 | 95 | 100 | 110 | 120 | 130 | 140 |
| ● | ● | ● | ● | ● | ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ||||
| Size 150〜250 | ||||||||||||||
| 150 | 160 | 170 | 180 | 190 | 200 | 230 | 250 | |||||||
Knurled round bars
Check / Stipe
| 6 | 8 | 10 | 12 | 16 | 18 | 19 | 20 | 22 | 24 | 30 |
|---|---|---|---|---|---|---|---|---|---|---|
| ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ |
※Pitch ・Check 1.11 ・Stripe 1.05
※Module 0.33
Please enquire about grades and sizes not in stock.
※all 2000L
Chemical composition
| Ni | Cr | Fe | C | Mn | Si | Co | P | S | Mo | Cu | N | Nb | Ta | Nb+Ta | W | V | other | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| min | 8.00 | 17.00 | ||||||||||||||||
| max | 10.00 | 19.00 | 0.15 | 2.00 | 1.00 | 0.20 | (0.60) |
※Above is standard values of JIS G4303. For further information, please contact us.
Mechanical properties
| Tensile Strength N/mm² | 0.2% Yield Strength N/mm² | Elongation ％ | Reduction of Area ％ | Hardness | |
|---|---|---|---|---|---|
| min | 520 | 205 | 40 | 50 | |
| max | HBW187 |
※Above is standard values of JIS G4303. For further information, please contact us.
International Specification Comparison chart
| Material | Round bars | Plates/Sheets | Pipes/Tubes | ||
|---|---|---|---|---|---|
| Seamless | Welded | ||||
| JIS | SUS303 | G4303/G4318 | G4304/G4305 | ||
| ASTM | S30300 | A582 | A895 | ||
| ASME | S30300 | SA582 | |||
| DIN/EN | 1.4305 | ||||
- Disclaimer
- All the information on this website is published in good faith and for general information purpose only and not for technical design purposes. We do not make any warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information on our website is strictly at your own risk. and we will not be liable for any losses and damages in connection with the use of our website.