SUS316L
Characteristics
SUS316L has lower carbon content than SUS316, which leads to minimal precipitation of carbides during welding and in high-temperature environments. For this reason, it is widely used for parts to be welded. Its austenite structure imparts outstanding toughness to this material even at cryogenic temperatures.
Stock Form and Sizes
◆1000mm ◎2000mm ▲3000mm ■3500mm ●4000mm ★2500mm～3990mm
Cold finished round barsSpecification：JIS G4318、ASTM A182/A276/A479、ASME SA182/SA276/SA479、NACE MR0175/MR0103、EN 1.4404
| Size 2〜8 | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 2 | 2.5 | 3 | 3.5 | 4 | 4.4 | 5 | 5.3 | 5.5 | 6 | 6.35 | 7 | 7.1 | 8 | 8.4 |
| ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎ | ◎● | ◎ | ◎ | ◎● | ● | ||
| Size 8〜15 | ||||||||||||||
| 8.95 | 9 | 9.52 | 10 | 10.8 | 11 | 11.3 | 12 | 12.7 | 13 | 14 | 14.3 | 14.6 | 15 | 15.87 |
| ● | ◎● | ◎● | ● | ● | ◎● | ● | ◎● | ● | ● | ● | ● | |||
| Size 16〜24 | ||||||||||||||
| 16 | 16.3 | 17 | 17.3 | 18 | 18.3 | 19 | 20 | 20.3 | 21 | 22 | 22.2 | 23 | 23.3 | 24 |
| ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ||||
| Size 25〜42 | ||||||||||||||
| 25 | 26 | 27 | 27.62 | 28 | 30 | 30.6 | 32 | 33 | 33.3 | 34 | 35 | 36 | 38 | 40 |
| ● | ● | ● | ||||||||||||
| Size 45～50 | ||||||||||||||
| 42 | 45 | 48 | 50 | |||||||||||
Peeled round barsSpecification：JIS G4303、ASTM A182/A276/A479、ASME SA182/SA276/SA479、NACE MR0175/MR0103、EN 1.4404
| Size 8〜26 | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 8 | 10 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 22 | 24 | 25 | 26 |
| ● | ● | ● | ● | |||||||||||
| Size 27〜48 | ||||||||||||||
| 27 | 28 | 30 | 32 | 33 | 34 | 35 | 36 | 38 | 40 | 42 | 44 | 45 | 46 | 48 |
| ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ||
| Size 50〜140 | ||||||||||||||
| 50 | 55 | 60 | 65 | 70 | 75 | 80 | 85 | 90 | 95 | 100 | 110 | 120 | 130 | 140 |
| ● | ● | ● | ● | ● | ▲ | ▲ | ▲ | ▲ | ▲ | ▲ | ★ | ★ | ★ | ★ |
| Size 150〜250 | ||||||||||||||
| 150 | 160 | 170 | 180 | 190 | 200 | 230 | 250 | |||||||
| ★ | ★ | ★ | ★ | ★ | ★ | ★ | ★ | |||||||
Chemical composition
| Ni | Cr | Fe | C | Mn | Si | Co | P | S | Mo | Cu | N | Nb | Ta | Nb+Ta | W | V | other | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| min | 12.00 | 16.00 | 2.00 | |||||||||||||||
| max | 15.00 | 18.00 | 0.030 | 2.00 | 1.00 | 0.045 | 0.030 | 3.00 |
※Above is standard values of JIS G4303. For further information, please contact us.
Mechanical properties
| Tensile Strength N/mm² | 0.2% Yield Strength N/mm² | Elongation ％ | Reduction of Area ％ | Hardness | |
|---|---|---|---|---|---|
| min | 480 | 175 | 40 | 60 | |
| max | HBW187 |
※Above is standard values of JIS G4303. For further information, please contact us.
International Specification Comparison chart
| Material | Round bars | Plates/Sheets | Pipes/Tubes | ||
|---|---|---|---|---|---|
| Seamless | Welded | ||||
| JIS | SUS316L | G4303/G4318 | G4304/G4305 | G3459 | G3459 |
| ASTM | S31603 | A182/A276/A479 | A240 | A312 | A312 |
| ASME | S31603 | SA182/SA276/SA479 | SA240 | SA312 | SA312 |
| DIN/EN | 1.4404 | ||||
- Disclaimer
- All the information on this website is published in good faith and for general information purpose only and not for technical design purposes. We do not make any warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information on our website is strictly at your own risk. and we will not be liable for any losses and damages in connection with the use of our website.